The NX-8 is a full-featured security system that uses advanced
technology for burglary, fire and environmental detection.
The NX-8 is a flexible security system that is both easy to install
and simple to use. With eight partitions and up to 48 zones,
the NX-8 can handle big or small residential and commercial
security needs.
SATEL
SPECIFICATIONS :
Model SATEL
up to 16 zones
- 8 on-board zones
- 2 zones on each keypad
- expandable by adding keypads or zone expansion modules
- NO, NC, EOL, 2EOL/NO or 2EOL/NC configurations
- 21 zone functions
- detector trouble monitoring feature 6 outputs
- 4 high power outputs 2,2A
- 2 open collector outputs
- fully programmable
- 41 functions 4 partitions system controlling
- LCD and LED keypads
- DTMF telephone using optional MST-1 module programming
- local by LCD and LED keypad
- local by PC via RS-232
- remote by integrated 300bps modem or external modem event log
- non-volatile
- 255 entries
- arm, disarm, trouble, alarm
- user functions
- event timestamp codes
- 1 service code
- 1 master code
- up to 13 user codes per partition
- up to 32 user codes total 4 timers
- automatic arm, disarm etc.
- supervision of guards telephone dialer
- monitoring - 2 monitoring station numbers
- call answering for remote system supervision
- voice and text messaging
- remote programming with PC via modem telephone signal analysis
- TBR-21 compatible telephone signal recognition
- advanced algorithm for re-transmission attempts messaging
- 8 telephone numbers (SM-2 voice synthesizer)
- 1 voice message
- 4 text messages sent to pagers RS-232
- local programming
- serial printer connection switching mode power supply
- 2,2A total capacity
- short-circuit protection
- battery condition testing
- deep discharge battery protection on-line event printout
- corresponds to monitoring station printout
- optional event filtering input module and user names printed according to system definition
on-line diagnostics of key system components
MAGNETIC CONTACT
DETECTOR
DD-105
DUALTechnology motion Sensor
MODEL : DD-105 SPECIFICATIONS :
Supply voltage 9 - 15 VDC Max. ripple 2 V peak-to-peak at 12 VDC
Alarm NC contacts, rated 80 mA at 30 VDC
Tamper NC contacts, rated 100 mA at 30 VDC
Alarm time 3.0 sec
Mounting height 1.8 to 3.0 m
Target speed Min. 0.2 m/sec - Max. 3.0 m/sec
Microwave frequency 2450 MHz
Microwave power 0.005 ?W/cm2 at 1.0 m
Coverage 7 curtains of 12 m
Range can be reduced to 7 m
Ambient conditions -10 ?C to +55 ?C; Max. 95% humidity
.Field of view 86?
IP/IK rating (with sealed cable entry) IP30, IK02
Dimensions (W x H x D) 61 x 123 x 58 mm
Prestige DT
Prestige DT SPECIFICATIONS : DIGITAL PIR & MICROWAVE DETECTION
15m Volumetric coverage.
Sealed optical system.
Digital temperature compensation.
Digital microprocessor technology.
EN 50131 grade 2.
Mirage DT Petwise
Mirage DT Petwise SPECIFICATIONS :
Voltage 10 - 16VDC.
Current 20mA typical at 12VDC.
Maximum Ripple 2Vpp at 12VDC (50 - 120Hz sinusoidal).
Alarm Output Normally closed (failsafe) voltage free relay contacts. Rated at 24VDC, 50mA protected by 18? series resistor.
Tamper Output Normally closed voltage free switch contacts.
Rated at 24VDC, 50mA. Alarm Period 2 - 3 seconds typical.
Walk Test LED Internal link to enable/disable.
Remote LED Disable Switched input between 0V and 12VDC (16V max). Latch Input Switched input between 0V and 12VDC (16V max).
Detection Method Passive Infrared and Microwave Doppler.
Pyro-Electric Detector Dual element, low noise.
Microwave Doppler S-Band (2.45GHz) Microwave PCB antenna. Complies with I-ETS 300 440 and FCC Part 15.
Power Density <5mW EIRP.
Exodus OH
Exodus OH SPECIFICATIONS :
Supply Voltage: 9 - 16VDC.
Current Consumption: 15mA typical.
Alarm Output: Built-in normally closed relay, open on alarm
24VDC 50mA, 18 °.
Dimensions: 107mm x 55mm.
Packed Weight: 200g (approximately).
EMC: Independently certified to EN50130-4 : 1996.
Design: Microcontroller based signal analysis.
Electronic drift compensation.
RF Immunity: No false alarms from 80MHz to 1GHz at 30V/m..
